Two stages of the Martlet 1 sounding rocket were launched at Ben Armine, Scotland, on the 3rd May 2012, as part of The Big Range 2012 launch campaign. Three videos of the launch are show below, which should be watched with sound – for the full launch report click here. More photos and information will be added to the launch report over the next few days.
The Martlet 1 rocket has an HD Go-Pro Hero 2 camera mounted in the nosecone, to take footage during the flight,. A window was needed in the fibreglass wall, so we made first made a mould of the outside of the nosecone outer surface using Siligum.
We then cut a porthole, and filled the porthole from the inside with clear polyester resin. The resin was sanded through the grades of wet-and-dry paper, then polished with Peek. There is very slight distortion, but a good optical clarity. The GoPro camera is mounted on an HDPE block that is connected to the noscone with 3 radial bolts.
We are proud to announce that the CUSF poster girl for May is Daniel Strange, the famed bearded superscientist. Isn’t she beautiful?
Today we had a pre-launch bash before Martlet 1 is launched next week. The rocket is (almost) ready to go now, with just a few finishing touches to be made. Many thanks also to Andy Hugh and Malcolm Jennings for busting a gut to get the rocket motors to us today. Some of the project’s sponsors also dropped by, such as Richard Hobbs from Cambridge Precision and Dr. Madsen Pirie (below), after whom the rocket is nicknamed the “Lord Madsen”.
To strengthen the fins, a fillet was put between the fins and the airframe, and then two layers of carbon fibre added over the top of the fillets. The fillets are made of two different parts: (1) epoxy clay at the front and back of the fillets (black), and (2) epoxy lightened with fillite in the centre of the fillet (gray). The epoxy clay is extremely strong and easy to shape, but is also very dense. It was only used at the front and back of the fillet, where it will not be covered by the carbon fibre.
After the fillets have been laboriously sanded smooth, carbon fibre was added over the fillets. When rockets fly at high speed the fins are prone to ‘flutter’, where the fins bend and twist at a high frequency. This can result in broken fins,. so some strengthening is required. We used two layers of 200gsm uni-directional carbon fibre, and Sicomin epoxy. The fabric is orientated so the fibres run down one fin, across the body tube and up the other fin, and this prevents the fins from fluttering.
The fabric is wetted out with epoxy and covered in peel ply (red) to help release excess epoxy and give a smooth finish. The peel ply is a plastic film that is designed to not stick to epoxy, and it is perforated with a series of small holes to allow excess epoxy to escape.
After a fair amount of hand finishing with a sander, and a thin gloss coat of the epoxy the result is very smooth and shiny.
The stages of the Martlet 1 rocket fit together with some finely machined aluminium coupling rings. The coupling rings are then restrained together by some 6mm plastic bolts. In flight, the primary method of separating the stages is to ignite the rocket motor in the next stage. As the pressure in the rocket motor ramps up, the high pressure causes the plastic bolts to shear, and the stages separate. The stage that has separated then deploys its parachutes from the open end, by using explosives protractors to release the spring drogue parachute.
If the rocket motor fails to ignite, however, it is important to have a secondary separation mechanism, so that the parachutes can be deployed. In this case, the flight computers detect that the motor didn’t ignite, as there is no acceleration, and separate the stages. The explosive protractors that deploy the spring drogue parachutes are strong enough to shear the interstage plastic bolts, and the stages separate, with the spring parachute close behind.
This video was taken at 300 frames per second and shows the front of one stage (bottom tube) and rear of the next stage (top tube) separating. As the protractors are activated the cap that restrains the spring parachute pushes the stages apart with 4kN force applied within 20ms of activating. The plastic bolts, whose heads are the white dots, are sheared and the orange and black spring parachute jumps out of the parchute section. In this video the spring parachute does not jump fully clear, as (a) the spring was not fully compressed, and (b) the bottom tube hits the floor before it can get out.
Over the weekend we assembled Martlet 1 in its 2-stage configuration (Stage1+3 of the 3-stage configuration). It is likely that the Martlet 1 rocket will be flown as a 2-stage rocket for its first outing at the Big Range launch, in little over a weeks time. The 2-stager is still pretty big – it should reach Mach 2 and ~35000ft, and is almost two stories high as shown in the picture below.
The Martlet 1 rocket has three stages, and each stage has two parachutes: (1) a small ‘drogue’ parachute that is deployed at apogee, so that the rocket comes down from high altitude in a controlled manner, but without drifting too far. (2) a large main parachute that is deployed near the ground for a soft landing.
Both the drogue and main parachutes were bought from Fruity Chutes and modified for better deployment. The drogue parachutes are 12″ in diameter, and we have added two features: (1) Nylon netting around the parachute lines, which means that it is now impossible for the drogue parachute lines to tangle. (2) A 50mm diameter spring has been sown into the centre of the drogue, and sown into a netting sock to keep it straight. The spring has two purposes, to keep the drogue stretched and inflated, and to jump out into the airflow when it is deployed. The drogue is packed into the rocket behind an aluminium cap, and the cap is restrained by two plastic bolts. To deploy the parachute, the plastic bolts are sheared by an explosive protractor, and the spring makes the drogue jump out of the rocket into the airflow.
The second feature that we have added to the recovery system is a proper parachute deployment bag. A deployment bag keeps the parachute packed in a neatly folded state, and makes sure that the parachute lines and the parachute are unfurled correctly into the airflow. The main parachute is deployed at 40m/s for this rocket, so it is important that the parachute deploys properly. The standard HPR practice of rolling the parachute, then wrapping it in its own lines, is much more likely to end up in a tangled parachute and a hole in the ground.
The deployment bags are made of red Cordura nylon, and white nylon tape. The inside of the bag is coated with polyurethane to reduce the friction when the parachute pulls out. On one side of the bag there are two tunnels for the parachute lines, on the other side there are five tunnels for the larger nylon tape that runs from the base of the parachute to the rocket. The parachute lines are folded into a U-shape, and the bend of the U is pulled through the tunnel (as shown on the left of the bottom photo). When the bag is deployed in the airflow, the lines start to go taut and then pull out of each tunnel in turn, then pull the parachute out of the bag. In this way the parachute and lines are fully stretched out when entering the airflow and will deploy without tangling.
Today we tried a method for vacuum bagging the tip-to-tip carbon fibre onto the fins of the rocket. The tip-to-tip carbon fibre has uni-directional fibres that run down one fin of the rocket, over the body tube and up the next fin. At supersonic speeds, the fins tend to flex and ‘flutter’, and can snap off the rocket. The tip-to-tip carbon fibre gives the fins a lot more flexural strength and should prevent this.
We created a vacuum bag that uses putty tape to seal on the aluminium leading edge of the fins. Because we only wanted to test the method, we covered the surface of the rocket in teflon sheet before adding the epoxy.
Although the vacuum bag gave a reasonable finish to the carbon fibre, it was quite a pain to get a good vacuum seal, and was quite an involved process. For the proper tip-to-tip carbon fibre we have decided to go for a normal wet lay-up and to manually smooth down the carbon fibre using rubber rollers. The epoxy that we are using for the lay-up is Sicomin, from Matrix Composites, which has good temperature stability without a post-cure. It is quite ‘fragrant’, however, hence some fairly hefty respirators….
Each stage of the Martlet 1 rocket has two parachutes: (1) a small sprung drogue parachute to bring the rocket down fast from high altitude (2) a much large maion parachute that is released near the ground to give a soft landing. The small parachute is deployed at apogee, and then near the ground the riser cable from the small parachute is released by a pyrotechnic mechanism. As the small parachute is released it pulls the main parachute out of the rocket body.
The release mechanism is shown below mounted on the bulkhead that sits between the motor and parachute sections of each stage. The pyrotechnic device is a protractor (gold in the photo below), which has an explosive charge and a piston inside it. The release mechanism has two parts, a housing that is bolted to the bulkhead,. and a slider with two 4mm pins. The kevlar riser cable (here just string) is looped around one of the pins until the mechanism is fired.
When the pyrotechnic device is fired, a piston is ejected with 2kN force, pushing out the slider and releasing the cable. The slider is then stopped from flying off by a catching plate (not shown).